Menu

Mobile racking in South African fruit stores

Featured

DEXION DEXION

Southern Storage Solutions – DEXION, has installed numerous mobile rack installations in conjunction with Barpro Storage which has increased the storage capacity of each facility without the expensive task of increasing the room size to cater for conventional pallet racking or drive in racking with all the associated extra refrigeration and electrical costs.

 

Traditionally pallets of packed fruit were stored by securing steel corner posts to each pallet and then storing another level of pallets on top. While doubling store capacity, this form of block storage effectively prevented stock rotation, increased stock damage and in some situations prevented adequate cooling.

As fruit packaging became further differentiated, accessing stock quickly for an order became practically impossible. Pallet racking was introduced into existing fruit stores to solve these problems. “Drive-In” racking made better theoretical use of the chilled space and reduced product damage. However the accessibility problem was not solved leading to “drive-in” lanes being only partially utilised for immediate access to individual product lines.

The alternative was to use fixed selective racking, giving immediate access to every pallet but greatly reducing storage capacity Mobile racking was first used in 1997 in a fruit store outside Grabouw in the Western Cape. Designed to take a combination of 2 200mm and 2 400mm pallets with a maximum weight of 1000kgs, the pallets were stored with the 1 000mm side facing and the 1 200mm side in the depth of the racks.

What is mobile racking?

Mobile racking consists of special rails that are laid in the floor during construction although rails can also be retrofitted in existing rooms provided the floor is suitable by levelling the rails on the existing surface and pouring a 150mm reinforced slab.

A low ramp is needed at the entrance. The mobile bases run on the rails and support pallet racking which is specially designed for use in a mobile application. The bases are motorised and energy efficient.

Maximum tonnage per base varies but should not exceed 360 tons. In larger stores mobiles are arranged in banks of up to 10 bases, each with its own moving aisle. The bases are controlled either by push buttons, remote control, or by an interface with the warehouse management system.

An access aisle is created at the push of a button. Safety measures include photoelectric beams down the length of each base and across the front of each mobile bank with additional emergency stops. To move one or multiple bases takes approximately one minute twenty seconds.

Mobiles are designed to give lighting signals so that the lights come on only in open aisles. This results in energy savings as each light produces heat which must be removed by the refrigeration system. The possibility of pallets breaking was removed by using a pallet support or saddle beams in the middle of each pallet slot.

These were painted yellow to assist with pallet placement especially on higher levels and increase rack strength. Another challenge arose when packed fruit stores remained in use for extended periods.

Improved ventilation in the mobiles allowed packed fruit to be chilled and store temperatures were reduced to around 0ºC. Frost heave, caused by moisture freezing under the floor, is not good for mobiles and recent installations have under floor insulation and heater mats to make sure this doesn’t happen.

The advantages of using mobiles in fruit stores have become apparent over the years. More expensive than “fixed selective” or “drive in”, mobiles can increase the practical capacity of a store by up to 75 or 80% while still giving immediate access to every pallet.

If the total cost of a proposed fruit store is divided by the practical pallet capacity the mobile option can be surprisingly competitive. Recently, mobiles have been installed in smaller stores, 3 and 2 pallets in the height with capacities of less than 450 pallets. Moving aisles have been widened to allow for the use of counterbalanced trucks and pallet bays extended allowing the placement of 3 pallets on the longer 1 200mm side.

Maximum pallet weights have increased to in excess of 1 300kg and storing five pallets in the height is now quite possible. Barpro Storage are able to manufacture smaller systems locally in their Cape Town manufacturing facility which cuts costs and reduces lead times.

The racking superstructure supplied by Southern Storage – DEXION is manufactured locally in Gauteng.

back to top

Industries

About us

Follow us

Follow us @BusinessNewsCT

BusinessNewsCT Revitalised Burma looks ahead to growth - https://t.co/3QvSM7l1zz https://t.co/eEH9Mn3zQV
BusinessNewsCT Atlas Copco expands range of dewatering pumps - https://t.co/Od3hEUMI2z #Atlascopco https://t.co/johuMN3iCZ